Home >

Garment Piece Rate Calculation

2011/1/21 11:16:00 65

Garment Piece Rate Calculation

About working hours


Generally speaking, man hour is the basis of labor price.

And piecework wage is inseparable from the cost of each process.


There are also standard specifications for man hour determination.


1. When a garment is about to be on line, the time measuring personnel should check the process table and the clothes one by one, so that they can have a general understanding of the work of the garment. If the obvious problems are found in the check, they should be immediately revised (for example, the process name is not standardized, the order is not standardized, etc.).


Two, in order to measure the accuracy of time, generally speaking, etc.

clothes

On line three days after the start of the test (less orders can be measured on the first day, but otherwise need to be indicated), the clothing has 3 dimensions, and the intermediate size should be measured.

If there are six sizes, it is divided into two segments, and the middle dimensions are measured (for example, children's series: 90CM, 95CM, 100CM, 110CM, 120CM, 130CM, 95CM and 120CM).


Three. The problems that should be noted in the process of measuring time:


1, the time users should stand at a distance away from the subjects, but the line of sight is not blocked, that is, they will not feel the time measured by the subjects, so that the subjects will work naturally.


2. The starting time of process measurement time: pick up from the subjects.

Cutting piece

- sewing - down the semi-finished products, the middle does not include pause, disconnection, chatting and so on, and 3 pieces of time are allowed to be measured continuously. (note that the number of pieces should not be allowed, and the number of pieces should be the same, for example, 2 pieces of front part =1.)


3, when measuring the time, we should pay attention to whether the movements of the subjects are standardized or not. If the movements are not standardized, they should be corrected immediately.


4, when measuring the time, we should pay attention to the quality of clothes sewing, such as whether the needle distance meets the requirements, whether the repair line is repaired, the needle path is not straight, the lace is too wrinkled or too straight, and so on, and register on the time table; if serious quality problems are found, it should be raised to the higher authorities immediately.


5. In the process of measuring time, the non-standard processes should be revised and unnecessary procedures should be deleted and the combined processes should be merged.


6.

Lace up

Method of measurement: we should first measure the length of the whole dress lace and then convert it to the actual length of the lace.


7, when sewing, if sewing and repair line, cut is done separately, should be divided into 2 parts of the time to add up, that is, sewing time + pruning time, and note the trim time on the remarks.

For example, the special car sew up the repair line and cut off after the vehicle break.


8. If there is a great difference in the time of two people doing the same process in time measurement, we should find out the causes and propose ways to improve it.


9, the speed of the driver is slow, the quality is poor, and the movement is not standardized.


10, the quality and quality of the tested persons should be registered on the time table.

  • Related reading

Introduction Of Basic Finishing Process For Common Sweaters

Learning Area
|
2011/1/21 11:12:00
49

Production Plan For Women'S Underwear Factory

Learning Area
|
2011/1/21 11:06:00
41

比例裁剪公式的正确取值

Learning Area
|
2011/1/21 11:04:00
78

A Brief History Of "Red Gang Tailors" In The History Of Chinese Costumes

Learning Area
|
2011/1/20 17:52:00
67

Brief Introduction Of Handcraft Personalized Custom Made Garment Technology

Learning Area
|
2011/1/20 17:50:00
63
Read the next article

2 Million Export Fake Nike Qingdao Checked

In January 21st, the sportswear and sports caps produced by small factories, coupled with fake "NIKE" trademarks, hanging cards, packaging bags and authorized documents, became famous brands and sold abroad, thus forming a black chain of counterfeiting and selling.